BIKES, WORK & FUN :HALL OF FAMEARCHIVECAR STUFF



The BSA-Bobber story


Part 2




There were a couple of bugs in the first build. The Norton belt drive ratios were all wrong; engine pulley was too small so the bike was revving like crazy at 60mph.

And there was a bizarre problem with the barrels. The bike was smoking and there was a leak from the front of the head gasket. Turned out the top barrel flange, despite having been refaced had pulled up around the front head bolts - raised a few thou'  in small mounds around the threaded holes. Never seen this before. 

With our attention now diverted towards our Bonneville projects, the bobber got sidelined for a few years. Indeed, we stole the gearbox out of it for Salt Flash in 2013.

It gathered dust for a couple of years.



With the Bonneville madness over with in 2016, I looked again at the little bobber.
The El Camino had been sold so it no longer had a role as its matching cargo and with what we'd learned from the Salt Flash build, I had some new ideas.
I'd already started accumulating parts and we had a use for the old engine in Jims new bobber project.

Salt Flash had alloy barrels, made from some blank castings from old grass-track racer Paul Grayson. I went back to Paul and bought another casting, his last one.
I figured to make these 3" bore and get 810cc capacity (using another Norton crank) so it seemed logical to use an A65 head instead of the smaller-chamber A10 one.
This hasn't been done too many times as its difficult to fit A65 barrels to A10 cases, but machining our own barrels made it possible.
So, a ton of machining later they were ready to go off for Nikasil coating.



Heres the cam-follower holes being machined.

It was decided to use 883 sportster pistons. Since I had some anyway!
The tops were machined to have a slight pop-up to get a bit of compression.
With the A65 head the ratio would have only been about 6:1!







On the same subject, turning to the A65 head, like the last build, squish chambers were wanted, and would bump up compression a bit more so he heads were welded up accordingly.

A broken fin was welded up and the exhaust ports were welded for threaded bosses






Heres the head machined, ported for bigger valves and assembled.

I had to modify some A10 pushrods with A65 ends on the top and tweak the exhaust rockers for clearance.

With the top end sorted out, the bottom end was next.

 I had a spare 750 Commando crank which had had the flywheel rebalanced for steel rods at some stage.
I didn't want steel rods but I did like the idea of a 270-degree crank.
So some good steel was bought and I got started machining.
And I bought a chunk of 7075 alloy and made some con-rods too.
Made a set for Jims engine as well while I was at it.
Theres the crank assembled with ARP bolts.

The whole rotating assembly went off to Basset-Down for balancing.
Obviously a special cam is needed for a 270 crank.
Newman Cams handled it no problem.
And there is the whole bottom end ready for assembly

Once again, the RH main bearing was converted to the needle-roller INA bearing with end-feed oiling.
Having used the gearbox in the Salt Flash bike, I grabbed a good deal on a LH shift Mk3 Commando 'box
This was rebuilt and parts bought to convert the gearshift over to the left.
A new belt drive was made using only the clutch pulley from the old one.  
I modified a Sportster clutch to fit in it and to fit the Norton mainshaft.
I mocked things up to see if there was room to fit an electric start. There was. So I did!  Again, a sportster starter was used and new engine plates were made.
You can see how they're shaped to fit around the starter.
Here is the new gearbox fitted during final assembly.
The RH footrest & brake pedal had to be completely re-done.
Obviously, the primary cases needed some work too.
A whole new inner primary was fabricated and the outer cover had a hump added.
Inner not quite finished here, a support bearing was added for the gearbox mainshaft. and  holes for the alternator & shifter yet to be done.

Complete primarys below.

Shifter shaft arragement below left.
Clearly the original ignition system wouldn't now work.
So a housing was fabricated to go in the original magneto location.
This was made to take an HD pickup plate with a special rotor.
A Harley type Twin-Tec module and coil was used to complete the system
.
The Twin-Tec unit is very adjustable and you can select single fire or dual fire. I'm not very keen on the RH cylinder firing halfway down the intake stroke, so its set at single fire mode.
All assembled and running! You Tube video:
BSA A10 Bobber. New engine.

New stainless exhausts were also done and it now has a period-correct front brake. Which isn't really a functional improvement!
Runs very well, but not too many miles on it yet as there is now a handling problem -  a speed wobble at about 60mph.
Measures in hand to deal with it.
Watch this space.